Aluminum wrap
Metal wrap can be added over new or sound fascia once any rot is gone.
Exterior Services
Fascia Repair Fanwood, NJ
A roofing contractor in Fanwood can fix soft, split or loose fascia along the roof edge, whether it is painted wood, PVC or wrapped in aluminum, and check the rafter tails behind the board while it is off. Call (908) 663-5020 to reach a local roofer.
The fascia sits right where water leaves the roof, so it is the first trim board to rot when that water goes the wrong way. Without a drip edge lapped into the gutter, runoff clings to the roof edge and wets the top of the fascia every storm. Once the wood is soft, gutter hangers pull loose and the gutter sags or tips forward.
Fascia damage does not stay in the fascia for long. The same water rots the ends of the rafters, the first course of roof decking and the soffit nailer. Aluminum wrap over wood can hide all of this, since the metal looks fine while the board behind it crumbles.
Before the visit, take a look along the roof edge from the ground. Write down which sides of the house show peeling paint, gaps or a sagging gutter. Mention whether the fascia is painted wood, PVC or covered in aluminum, and how old the gutters are.
If the problem goes deeper than it first looked, a Fanwood roofer may also recommend soffit repair or gutter installation.
Dealing with this in Fanwood, NJ right now? Call (908) 663-5020 and describe the problem to a roofer who works in Fanwood.
Call nowThe process
The fascia repair process
Good fascia work deals with the roof edge, the gutter and the board together.
Inspect the roof edge
The roofer checks the drip edge, the first course of shingles, the gutter pitch and the downspouts above the damaged fascia. The length of the damage decides how much board is replaced.
Take down the gutter
The gutter section over the damage is unhooked and set aside so the fascia can come off. Old spikes and loose hangers are not reused.
Inspect behind the board
Soft rafter tails are cut back and sistered with new lumber, and rotted decking at the edge is replaced. New fascia nailed to rotten rafter ends will loosen again.
Replace the boards
A replacement board matched to the existing size goes up, sealed at the ends and joints. PVC and composite boards do not rot and hold paint well.
Fix the edge flashing
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. This is the piece that keeps the new fascia dry.
Rehang the gutter
The gutter goes back up with new hidden hangers screwed into solid wood, pitched toward the downspout. The finished edge is checked with a hose or after the next rain.
What is included
Common fascia repairs
Soft fascia
Damaged fascia is replaced with primed wood or PVC so gutters have solid backing.
Framing repair
Rotted rafter ends behind the fascia are sistered or rebuilt before the fascia goes back on.
Gutter rehanging
Sagging gutters are rehung on solid fascia with new hangers at the right slope.
Edge flashing
Drip edge is added where the roof edge had none which stops the rot from coming back.
Related service
Fascia Board Replacement Fanwood, NJ
Fascia board replacement means taking off whole lengths of board rather than patching short sections. Replacing the whole run gives the roofer a clear look at every rafter tail and the edge of the roof deck. The choice of material affects upkeep, since wood needs paint while PVC and wrapped boards do not.
For many Fanwood homes it makes sense to replace fascia while the gutters are off for replacement anyway. Be wary of any plan that covers rotted boards with metal instead of replacing them. Matching the board width keeps the soffit and gutter lined up.
Related service
Fascia Board Repair Fanwood, NJ
Fascia board repair handles damage that is limited to a few spots, such as a rotted corner, the area under a leaky gutter seam or a section by a downspout. The new piece is joined with an angled scarf joint so the seam is strong and less likely to open. For a shallow soft spot, an epoxy consolidant and filler can restore the surface without cutting the board.
The repair is only worth doing if the water source is fixed at the same time. That usually means resealing a gutter seam, unclogging a downspout or adding drip edge over the repaired section. Once the wood is primed and painted on all sides, a repaired section can last as long as the rest of the board.
Local help
Fascia Repair Near Me
In Fanwood, fascia tends to fail first on the sides of the house where gutters clog fastest. From Fanwood out to neighboring towns such as Westfield, Plainfield, Watchung and Mountainside, older roof edges often need board and rafter tail repair while newer ones more often need drip edge and gutter fixes, which is why keeping gutters clear does so much to protect the fascia.
Need fascia repair around Fanwood? Call (908) 663-5020 for a Fanwood roofer who serves the towns around it too.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Fanwood is busiest after a hard winter and before the next one.
Why call
Why not wait
Drier ceilings
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Fanwood and nearby towns.
Clear next steps
Ask your questions before you agree to anything.
Common questions about fascia repair
Should I cover rotted fascia with metal?
Covering rotted wood with aluminum hides the rot instead of stopping it. Since gutters hang from the wood, the problem shows up later as a falling gutter. Fix the wood, then add wrap over it.
Why do gutters pull away from the fascia?
Gutters hang from the fascia, so their strength depends on it. Soft fascia lets the fasteners work loose, which is often the first sign of rot. Repairing the fascia and rehanging the gutter with hidden hangers fixes both problems at once.
What causes fascia boards to rot?
Most fascia rot traces back to the roof edge and the gutters. Clogs, bad seams and the lack of a drip edge are the usual culprits. Bare end grain and failed paint let water soak in faster.
Do I need new fascia boards or just a repair?
Spot repairs work well for rotted corners and short stretches. Long stretches of soft wood are better handled by replacing the whole board. Either way, the rafter tails behind the board need to be checked.
Which fascia material lasts longest?
Primed wood, PVC, composite and aluminum-wrapped wood are the usual choices. Primed wood is easy to match on older homes but needs regular paint. No material holds up if water keeps running behind the gutter.
More questions? Call (908) 663-5020
Other services that may help
Soffit Repair
Fixing damaged soffits, blocked soffit vents and gaps where animals get in, before rot spreads into the fascia and rafter tails.
Learn moreGutter Installation
New gutters and downspouts formed to fit the house, with the right size, pitch and outlet placement, from K-style aluminum to half-round and copper.
Learn moreGutter Repair
Fixing gutters that drip at the corners, sag between hangers or pull away from the fascia, so roof water drains where it should again.
Learn moreRoof Repair
Repairs for missing shingles, lifted tabs, cracked pipe boots, loose flashing and soft decking, matched to what is actually wrong up top.
Learn more
Looking for something else?
See all roofing servicesNeed fascia repair in Fanwood, NJ?
Call (908) 663-5020 for a local roofer in Fanwood and nearby towns.